Author Topic: Gearing up for 3rd try..  (Read 2201 times)

0 Members and 1 Guest are viewing this topic.

Offline Lastfling

  • Regular Member
  • **
  • Posts: 98
  • Thanked: 9 times
  • Gender: Male
  • Location: NC
Gearing up for 3rd try..
« on: March 07, 2018, 12:41:08 pm »
Nucs are suppose to be here around 4/1.  All hive bodies painted / re-painted (as the case may be).  I built and leveled a new hive stand using  cinderblock and 4x4's yesterday as my previous one could only hold one hive.  The new one has the potential for 4 hives at least as the 4x4's are 10' long.  I was going to cut them down, but decided to leave them as they are for the time being. 

Now for a really dumb question.  What holds/keeps the hive on the stand?  Weight alone?  I ask because just positioning one hive made me wonder what's going to happen with a full bottom deep when removing the top deep for inspection?   It seemed the remaining components - deep / bottom board -  wanted to slide around on the stand (4x4).   For clarification the stand itself is cinderblock piers with (2) 4x4's laid parallel between the piers.  Total height from ground to top of 4x is 16".    Does the bottom board need to be anchored to the 4x4 in some way?    Am I overthinking this?  Which I may be, as the hives from last year weren't anchored, but they were lower to the ground just sitting on pieces of 4x4. 


Offline Some Day

  • Senior Member
  • ***
  • Posts: 196
  • Thanked: 18 times
  • Gender: Male
  • Location: Iowa
Re: Gearing up for 3rd try..
« Reply #1 on: March 07, 2018, 12:50:25 pm »
You could use hive staples to fasten bottom boards to your 4x4's. 

https://www.mannlakeltd.com/hive-staples

Offline Lastfling

  • Regular Member
  • **
  • Posts: 98
  • Thanked: 9 times
  • Gender: Male
  • Location: NC
Re: Gearing up for 3rd try..
« Reply #2 on: March 07, 2018, 05:07:30 pm »
That’s a possibility -Thanks

Offline neillsayers

  • Gold Member
  • ****
  • Posts: 2173
  • Thanked: 197 times
  • Gender: Male
  • Location: Arkansas Ozarks, U.S.A.
Re: Gearing up for 3rd try..
« Reply #3 on: March 07, 2018, 05:17:12 pm »
I place my stands on 4x4s raised on concrete blocks. Hives are about 2' apart. Then I screw 2x2s on either side of the stand so I can pull a pallet strap or piece of rope around hive and 2x2s to keep the hive from toppling over in a high wind.

The bees tend to propolize the bodies together and to the bottom board, so if I need to pull a box off it rarely pulls the bottom box off the stand. (Think that was what you were asking. Hope it helps.) :)
Neill Sayers
Herbhome Bees
USDA Zone 7a

Offline Wandering Man

  • Gold Member
  • ****
  • Posts: 1839
  • Thanked: 175 times
  • Gender: Male
    • Life Lessons from dogs, bees and others
  • Location: Victoria, Texas
Re: Gearing up for 3rd try..
« Reply #4 on: March 07, 2018, 05:18:40 pm »
I used straps to hold down the hives when Harvey blew through last August.

Otherwise, I've not had any problem with wind gusts up to 40 mph.  But there is a brush break in front, a fence and workshop behind, so they probably never see 40 mph winds.

Before Harvey:


After Harvey:


Never argue with drunks or crazy people

Offline Lburou

  • Gold Member
  • ****
  • Posts: 2284
  • Thanked: 315 times
  • Location: DFW area, Texas, USA, growing zone 7a
Re: Gearing up for 3rd try..
« Reply #5 on: March 07, 2018, 05:20:36 pm »
I tie hives down with a rope.  The rope is easily removable, does not poke holes in the hive, and is adjustable to all hive heights.


Lee_Burough

Offline Lburou

  • Gold Member
  • ****
  • Posts: 2284
  • Thanked: 315 times
  • Location: DFW area, Texas, USA, growing zone 7a
Re: Gearing up for 3rd try..
« Reply #6 on: March 07, 2018, 05:23:40 pm »
This is how the hives did during an actual tornado in our backyard...





Lee_Burough

Offline LazyBkpr

  • Gold Member
  • Posts: 6842
  • Thanked: 205 times
  • Gender: Male
  • www.outyard.net
    • The Outyard
  • Location: Richland Iowa
Re: Gearing up for 3rd try..
« Reply #7 on: March 08, 2018, 07:24:38 am »
That's impressive Lee! Glad your bees weathered that storm so well!

   I move hives about too much to screw them down, but that would work.   I also have a stand that is cinder blocks with 4x4's and I just set the hives on them, and yes, weight is all that holds them down. I don't have many problems even with the winds we have here. Tornado three miles away blew one of my top covers off. A guy mowing with a skid steer with a mower front attachment hit one of my hives and knocked it over. Don't have many issues with them if the stands are sturdy.   
Drinking RUM before noon makes you a PIRATE not an alcoholic!

*Sponsor*

Offline Lastfling

  • Regular Member
  • **
  • Posts: 98
  • Thanked: 9 times
  • Gender: Male
  • Location: NC
Re: Gearing up for 3rd try..
« Reply #8 on: March 08, 2018, 12:14:38 pm »
Thanks all for the responses. I would have answered back sooner, but for whatever reason Tapatalk tells me I don't have permission to post.